Find great deals for Omron E5ax Temperature Controller E5ax-a-f. Shop with confidence on eBay!. E5AX-VAA Omron Automation and Safety Controllers datasheet, inventory, & pricing. E5AX-A by Omron | OMRON TEMPERATURE CONTROLLER | Shipping to + countries worldwide.

Author: Dourn Dajora
Country: Syria
Language: English (Spanish)
Genre: Sex
Published (Last): 11 May 2017
Pages: 126
PDF File Size: 12.28 Mb
ePub File Size: 18.29 Mb
ISBN: 307-7-39204-684-5
Downloads: 41905
Price: Free* [*Free Regsitration Required]
Uploader: Meztisar

Select this function by pressing the Display Key three times in display level 0. Actual displays vary with models and switch settings.

Omron E5ax-ah E5AXAH Temperature Controller C

Alarm Mode Selector SW Level Key Press for 2 seconds minimum to change levels to set different groups of parameters. Pin number Pin setting Not used. It is factory-set to position 2 to designate a K-type chromel-alumel thermocouple temperature sensor. Level 2 In level 2, selected input sensor, and modes for alarm output can be monitored. Display Basically, the temperature range that can be measured is determined by the temperature sensor to be used.

Turn on power and press the Level Key for at least two seconds. If this difference is too great, a drastic change will result. While mot is displayed, use the Up and Never calibrate the motor during control operation. HEA In the interest of product improvement, specifications okron subject to e5axx without notice. This is the initial mode when power is turned on for the first time.


RS and terminals are shown. Optimum PID control with feed-forward control circuitry. Displayed temperature 0 without shift Lower setting limit Press a.

This DIP switch selects the operation modes listed in the following table. All units are in millimeters unless otherwise indicated.


Derivative Time Rate Time: Tighten the screws of omrln mounting brackets with your fingers. Then press the Display Key until calb is displayed. Do not install the Temperature Controller in a location exposed to excessive dust or corrosive gases.

Models with communications capabilities also available. Automatic Output Mode In automatic output mode, the control will function automatically. Process value 0 Main setting Press a. Integral Time Reset Time: Use the Up and Down Keys to adjust the setting if required value must be between 1 and s in the units of 1 s. While auto-tuning omdon in operation, the auto-tuning indicator on the front panel will flash.

The maximum total cable length must not e5zx the following limits. Always set the following parameters when installing the controller.

Omron E5ax-ah E5AXAH Temperature Controller C | eBay

After that, the Temperature Controller automatically adjusts the PID constants using the limit cycle method. Auto-tuning can be carried out regardless of whether the Temperature Controller is performing reverse heating or normal cooling operation. The count value for omrkn fully open position will be set. Not displayed in automatic output mode.


Up Key Press to increase the main setting or other parameters. Input type, alarm mode 1. Use lead wires having a small resistance for temperature resistance thermometers. Hold down the Level Key again for 2 seconds minimum to display o on the PV display.

Therefore, take this time delay into consideration when designing sequenced circuits which incorporate a Temperature Controller. Alarm Indicator Lights when the alarm output is ON. Do not tighten the terminal screw with excessive force, because doing so may damage them. Process value see note e5qxvalve position 1.

If a display does not appear as expected, check your switch settings. The switch is factory-set to position 2, i. Press the Display Key to return to sl—l. Outputs the temperature data within the set limits. Always switch to the manual output mode before changing the proportional band. Sequenced Circuits Several seconds are required until the relay in turned ON after power has been supplied to the Temperature Controller.

Upper setting limit Press a.

To stop auto-tuning, hold down the Level Key and Mode Key again simultaneously for 1 second minimum. Alarm hysteresis db Proportional Band: