Cerber C52 is a burglar alarm system with 6 fully programmable zones on the motherboard, expandable to 12 by doubling and / or using keypad zones (each. Cerber c Users Guide – Download as PDF File .pdf), Text File .txt) or read online. Cerber C Zone and 2-Partition Burglary Control Panel For your home and office User’s Guide Doc / / version 1. INTRODUCTION.

Author: Vudot Vudojin
Country: Reunion
Language: English (Spanish)
Genre: Life
Published (Last): 20 March 2005
Pages: 92
PDF File Size: 7.32 Mb
ePub File Size: 18.86 Mb
ISBN: 850-1-11147-594-3
Downloads: 18783
Price: Free* [*Free Regsitration Required]
Uploader: Kazrakazahn

Allowed default rights for these user codes are: The 2nd to 45th user codes are not programmed by default.

System Troublesand when enetring the menu: Then enter the following sequence: Before entering this section the PC modem must be passed in the waiting status for control panel calls. If the warning devices ecrber on a different level of the residence from the bedrooms, then they are less likely to waken or alert people inside the bedrooms.

Once the system enters section [], it will exit this cerbee only after [ ] key is entered the control panel will not leave this section automatically, 2 minutes after the last key pressing any more.

The following sequence will be introduced: After a voice dialing sequence was finished, cedber control panel will begin the next sequence similarly until the sequence number programmed in this section was over.

This trouble indicator will appear if wiring between the siren and the control panel is shorted, cut-off or there is an overload on the siren control wire a 3K3 resistor must be connected across the bell terminals.

Cerber c612 Users Guide

The system time and date programming is allowed to the master user only if the appropriate option does not disabled by programming see the appropriate option within [] section. The control panel can report upon remote interrogation calls and to the follow me phone numbers, too up to 8 voice messages only when there it is using the MPV8 voice module; voice messages are specific to alarms on 1 to 8 1zones.


Moreover, smoke detectors have d612 limitations. If [8] key is pressed and the zone 3 LED is blinking, then the 8-th memorized alarm was triggered by zone 3.

Cerber C – Roel Design

Quick Arming Modes Arming without user codes Quick arming features allow the system to be quickly armed by any person who may not own a user code. If the buzzer warnings were enabled by programming, during the exit delay the keypad buzzer will sound warning beeps. Cfrber each key pressing, the keypad buzzer will sound a short beep.

Press [ ] key to exit system trouble displaying menu. LED interpretation, in case of pressing a key from 1 to 9, is accordingly performed: After entering a valid user code within one of the previous sequences, all keypad LEDs will be ON for a little while and the keypad buzzer will sound 6 acceptance beeps only KPP. The keypad buzzer will sound 6 confirmation beeps and the panel exits the [] programming section, waiting for a new command to enter another section or [ ] key to exit the main programming menu.

These events occur by activating the correspondingly 24h defined zones, or by simultaneously pressing a combination of keys from keypad: This procedure can be performed also by pressing c6112 [BYPS] key.

In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials, overloaded electrical circuits, children playing with matches, or arson.

Even if no successful command was performed, the user should press [ ] key in order to exit from the display of PGM1 to PGM6 status. If any cerner condition occurs, it needs to be solved f612 arming to assure a proper function for system.


Please note the backup battery is continuously charged while AC power is present and if this trouble persists for a long time that means the battery must be replaced.

Cerber c Users Guide – Documents

The master user only may see own rights as they were established by the installer previously and, if the master user wants to change his rights he must call his installer.

Other Operation Commands Performed by the master user Some of programming sections, which are dedicated to the installer, are accessible to the master user, too. The BELL output uses a fuseless circuit and it will automatically shut down if the current exceeds 2.

The menu command list is the following: If the buzzer warnings were enabled by programming, during the exit delay time, the keypad buzzer will sound warning beeps. This trouble indicator will be ON when: The keypad buzzer will sound 3 beeps after each 3-digit group and 6 beeps after the last one.

An overload on the siren control wire is detected only during when a condition has occurred which 21 would activate the bell output e. The following sequence will be performed: If the siren sound is stopped while the system is disarmed, using a proper user code, the system will not be armed in the meantime, only the sounders stops.